How to Fix Warped Wood

You will commonly see wood that has been formed in many different places. You need to know though that once you will have this situation, there are still many ways for you to be able to fix it.

Wood that has warped is defined as a deviation from its natural flat surface. This can be due to the stress that has been applied to it. It might also shrink in the process. The wood can also warp because of the moisture that has been absorbed and released by it.

The uneven moisture is one of the most common reasons why warping happens.

If you want to address warping though, there are many ways to do it.

Materials needed:

  • Winding stick
  • Large towels and plastic wraps
  • Steam iron
  • Clamps

What you need to do

Using a winding stick first

Image Source: https://www.pinterest.ph/pin/605100899910066878/

The first thing that you need to do is to determine the type of warp that you have. You can do this once you will be using a winding stick. A pair of a winding stick is the one that will help you identify the twist or bow. You will need to look for level sticks, one you are able to form an X shape then this means that it has some twisting on its surface. In order to address this one then you need to plane the wood diagonally along its high line.

You can use a single winding stick of you want to determine if the wood is bowed. Drag the stick along the wood and if there is a space between the sticks and the wood then you can have a warp.

Using an Iron

Image Source: https://carveyourcreation.com/how-to-straighten-warped-wood

Step 1

The very first thing that you need to do this one is to wrap the wrapped wood in large moist towels. You need to ensure that the warped region is fully covered. You also need to make sure that the towels will endure the high temperatures that the iron will give out.

Image Source: https://www.wikihow.com/Unwarp-Wood

Step 2

Drench the towels thoroughly to get rid of the excess water. Place the warped wood on a flat surface. It is important that it is also label top endure the high temperature of the iron. See to it that the concave surface will be facing down. Set the iron to its highest level and heat it up at around 2-5 minutes. You can have better results once you will choose to use a steam iron.

Image Source: https://www.wikihow.com/Unwarp-Wood

Step 3

The next thing that you need to do is to press the iron on the warped surface. Slide the iron on the entire surface of the wood while applying an even pressure. Hold the iron in each position at around 5-10 seconds. To prevent any damage then you must not leave the iron box unattended at any point. This will also help you avoid burning the towel that you are using. Check once in a while if the warping has stopped. Once you have determined that it has been corrected then you can choose to stop the process and allow the wood to dry.

Image Source: https://www.wikihow.com/Unwarp-Wood

Using Pressure

Image Source: https://carveyourcreation.com/how-to-straighten-warped-wood

Step 1

Using a moist towel, see to it that you will be covering the warped wood on the curved section that it has. You have to use a paper towel when doing this process. You need to make sure that it will be large enough to cover the warped area. Soak the towel with water and remove the excess by drenching it. See to it that the towel will be faced on the concave section to bring the wood to its normal state.

Image Source: https://www.wikihow.com/Unwarp-Wood

Step 2

You now need to wrap the wood with plastic and ensure a tight and secure fit. This will help in drenching evaporation and maintains the moisture on the wood.

Image Source: https://www.wikihow.com/Unwarp-Wood

Step 3

Clamp the warped section of the wood and make sure that you will have the right tightness until you are able to straighten it on its warped region. You need to be careful though as over tightening can cause a split in the wood.

Image Source: https://www.wikihow.com/Unwarp-Wood

Step 4

Leave the wood for around a week and regularly observe for any possible damage. You need to make sure that the area to where you are placing the wood will have high temperatures at around 65 degrees.

Image Source: https://www.wikihow.com/Unwarp-Wood

Step 5

Remove the plastic wrap and the paper towels as well as the clamps. Once the warping has been corrected then you have to leave the wood to dry before using it.

Image Source: https://www.wikihow.com/Unwarp-Wood

Conclusion

There are many various ways on how you are able to correct wood warping. Choosing the one that you find plausible is the one that you should choose to correct this issue.

  • January 5, 2019
  • DIY
Click Here to Leave a Comment Below 0 comments